2023年7月9日发(作者：)

元器件交易网ERO JUNCTION FIELD EFFECT TRANSISTORNE3514S02K BAND SUPER LOW NOISE AMPLIFIER

N-CHANNEL HJ-FET

FEATURES

• Super low noise figure and high associated gain

NF = 0.75 dB TYP., Ga = 10 dB TYP. @ f = 20 GHz

• Micro-X plastic (S02) package

APPLICATIONS

• 20 GHz-band DBS LNB

• Other K-band communication systems

ORDERING INFORMATION

Part Number Order Number Package Quantity

2 kpcs/reel

10 kpcs/reel

Marking

D

Supplying Form

• 8 mm wide embossed taping

• Pin 4 (Gate) faces the perforation side

of the tape

NE3514S02-T1C NE3514S02-T1C-A

S02 (Pb-Free)

NE3514S02-T1D NE3514S02-T1D-A

Remark To order evaluation samples, contact your nearby sales office.

Part number for sample order: NE3514S02

ABSOLUTE MAXIMUM RATINGS (TA = +25°C)

Parameter Symbol Ratings Unit

Drain to Source Voltage

Gate to Source Voltage

Drain Current

Gate Current

Total Power Dissipation

Channel Temperature

Storage Temperature

VDS 4 V

VGS

ID

−3 V

IDSS mA

IG 100

µA

Ptot Note165 mW

Tch +125 °C

Tstg −65 to +125 °C

Note Mounted on 1.08 cm2 × 1.0 mm (t) glass epoxy PCB

CautionObserve precautions when handling because these devices are sensitive to electrostatic discharge.

Document No. PG10593EJ01V0DS (1st edition)

Date Published February 2006 CP(N)

元器件交易网3514S02RECOMMENDED OPERATING CONDITIONS (TA = +25°C)

Parameter Symbol MIN. TYP. MAX. Unit

Drain to Source Voltage

Drain Current

Input Power

VDS 1 2 3 V

ID 5 10 15 mA

Pin

− −

0 dBm

ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified)

Parameter Symbol Test Conditions MIN. TYP. MAX. Unit

Gate to Source Leak Current

Saturated Drain Current

Gate to Source Cutoff Voltage

IGSO

IDSS

VGS (off)

VGS = −3 V

VDS = 2 V, VGS = 0 V

VDS = 2 V, ID = 100

µA

VDS = 2 V, ID = 10 mA

VDS = 2 V, ID = 10 mA, f = 20 GHz

−

15

−0.2

40

−

8

0.5 10

µA

40

−0.7

55

70 mA

−2.0 V

−

mS Transconductance gm

Noise Figure

Associated Gain

NF 0.75 1.0 dB

10

−

dB Ga

2

Data Sheet PG10593EJ01V0DS 元器件交易网3514S02TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified)

TOTAL POWER DISSIPATIONvs. AMBIENT TEMPERATURE250Total

Power

Dissipation

Ptot

(mW)DRAIN CURRENT TO SOURCE VOLTAGE100Mounted on Glass Epoxy PCB(1.08 cm2 × 1.0 mm (t) )Drain

Current

ID

(mA)26040VGS = 0 V–0.2 V20–0.4 V–0.6 V1.0Drain to Source Voltage VDS (V)2.02500Ambient Temperature TA (˚C)DRAIN CURRENT TO SOURCE VOLTAGE80VDS = 2 VDrain

Current

ID

(mA)6040200–2.0–1.0Gate to Source Voltage VGS (V)0MINIMUM NOISE FIGURE,ASSOCIATED GAIN vs. FREQUENCY2.0Minimum

Noise

Figure

NFmin

(dB)20VDS = 2 VID = 10 mA1814121086NFmin4251Associated

Gain

Ga

(dB)1.81.61.41.21.00.80.60.40.20.00Ga16

Frequency f (GHz)

Remark The graphs indicate nominal characteristics.

Data Sheet PG10593EJ01V0DS

3 元器件交易网3514S02S-PARAMETERS

S-parameters/Noise parameters are provided on the NEC Compound Semiconductor Devices Web site in a form

(S2P) that enables direct import to a microwave circuit simulator without keyboard here to download S-parameters.

[RF and Microwave] → [Device Parameters]URL /

4

Data Sheet PG10593EJ01V0DS 元器件交易网 MEASURING LAYOUT PATTERN (REFERENCE ONLY) (UNIT: mm)

2.802.602.060.641.7 mm/R.200312.6Reference Plane1.71.7Reference Plane(Calibration Plane)(Calibration Plane)φ0.3 THL2–uX Ver. 16.0

RT/duroid 5880/ROGERS

t = 0.254 mm

εr = 2.20

tan delta = 0.0009 @10 GHz

Data Sheet PG10593EJ01V0DS

NE3514S025

元器件交易网3514S02PACKAGE DIMENSIONS

S02 (UNIT: mm)

6

(Top View)(Bottom View)3.2±0.20.65 TYP.2.2±0.211.P2Y.T

5.D0±2.02424233(Side View)2.2±0.21.750.0±51.03.2±0.2PIN CONNECTIONS1. Source2. Drain3. Source4. Gate

Data Sheet PG10593EJ01V0DS

2.6±0.11.5

MAX.元器件交易网3514S02RECOMMENDED SOLDERING CONDITIONS

This product should be soldered and mounted under the following recommended conditions. For soldering

methods and conditions other than those recommended below, contact your nearby sales office.

Soldering Method

Infrared Reflow

Soldering Conditions Condition Symbol

Peak temperature (package surface temperature)

Time at peak temperature

Time at temperature of 220°C or higher

Maximum number of reflow processes

Maximum chlorine content of rosin flux (% mass)

: 260°C or below

: 10 seconds or less

: 60 seconds or less

: 3 times

: 0.2%(Wt.) or below

: 350°C or below

: 3 seconds or less

: 0.2%(Wt.) or below

HS350

IR260

Preheating time at 120 to 180°C : 120±30 seconds

Partial Heating Peak temperature (terminal temperature)

Soldering time (per side of device)

Maximum chlorine content of rosin flux (% mass)

Caution Do not use different soldering methods together (except for partial heating).

Data Sheet PG10593EJ01V0DS

7 元器件交易网

Subject: Compliance with EU Directives

CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant

with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous

Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive

2003/11/EC Restriction on Penta and Octa BDE.

CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates

that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are

exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.

All devices with these suffixes meet the requirements of the RoHS directive.

This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that

go into its products as of the date of disclosure of this information.

Restricted Substance

per RoHS

Lead (Pb)

Mercury

Cadmium

Hexavalent Chromium

PBB

PBDE

Concentration Limit per RoHS

(values are not yet fixed)

< 1000 PPM

< 1000 PPM

< 100 PPM

< 1000 PPM

< 1000 PPM

< 1000 PPM

Concentration contained

in CEL devices

-A -AZ

Not Detected (*)

Not Detected

Not Detected

Not Detected

Not Detected

Not Detected

4590 Patrick Henry Drive

Santa Clara, CA 95054-1817

Telephone: (408) 919-2500

Facsimile: (408) 988-0279

If you should have any additional questions regarding our devices and compliance to environmental

standards, please do not hesitate to contact your local representative.

Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance

content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information

provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better

integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate

information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL

suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for

release.

In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to

customer on an annual basis.

See CEL Terms and Conditions for additional clarification of warranties and liability.