2023年7月6日发(作者：)

linux下使⽤shell命令通过wpa_cli控制wpa_supplicant连接wifi最近在调试wifi，已经把wpa_supplicant ⼯具编译打包好了，为了测试wif驱动及wifi模块是否ok，需要⽤shell命令临时启动wifi服务连接wifi热点测试。⾸先板⼦启动⽤ifconfig后先把wlan0启动起来root@p1:/ # busybox-smp ifconfig wlan0 up

root@p1:/ # busybox-smp ifconfig

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:13931 errors:0 dropped:0 overruns:0 frame:0 TX packets:13931 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1

RX bytes:773000 (754.8 KiB) TX bytes:773000 (754.8 KiB)wlan0 Link encap:Ethernet HWaddr 7C:DD:90:EC:F2:1E

UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:2 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)现在wlan0已经up起来了。然后启动wpa服务，需要⼀个wpa_,我的配置如下update_config=1ctrl_interface=/data/misc/wifi/wlan0eapol_version=1ap_scan=1fast_reauth=1其中的ctrl_interface就是⽤来和wpa_cli通信使⽤，其原理是wpa_supplicant是个⼲活的wifi服务器（⽐如连接wifi，断开wifi，启动热点等），wpa_cli就是个客户端，通过本地socket通信连接上wpa_supplicant服务器，发命令叫他⼲活。现在把wpa_supplicant服务启动起来root@p1:/ # wpa_supplicant -iwlan0 -c/system/etc/wifi/wpa_ -B-B是在后台运⾏，如果想要看过程中的详细log，可以加上参数-dd，然后⽤logcat同时看log。现在wpa服务已经起来了，下⾯⽤wpa_cli客户端连接到wpawpa_cli -iwlan0 -p/data/misc/wifi/wlan0

wpa_cli v2.1-devel-4.4.2Copyright (c) 2004-2013, Jouni Malinen and contributorsThis software may be distributed under the terms of the BSD README for more ctive mode>

以上log显⽰已经连接上wpa了如果wpa异常，cli就⽆法连接会看到⼀下log，然后wpa_cli处于阻塞状态Could not connect to wpa_supplicant: wlan0 - re-trying现在我们的wpa_cli已经连上了，可以通过命令来查看当前的wifi状态> statuswpa_state=DISCONNECTEDp2p_device_address=7c:dd:90:ec:f2:1eaddress=7c:dd:90:ec:f2:1e<3>CTRL-EVENT-STATE-CHANGE id=-1 state=0 BSSID=00:00:00:00:00:00 SSID=现在我们还没有连接⽹络，⾸先使⽤scan命令扫描⼀下附近的wifi⽹络，然后使⽤scan_results显⽰扫描的结果> scanOK<3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-SCAN-RESULTS

<3>WPS-AP-AVAILABLE <3>CTRL-EVENT-STATE-CHANGE id=-1 state=2 BSSID=00:00:00:00:00:00 SSID=scan scan_interval scan_results> scan_results

bssid / frequency / signal level / flags / ssid50:fa:84:50:31:5e 2472 -75 [WPA-PSK-CCMP][WPA2-PSK-CCMP][ESS] xe6xb5xb7xe8xb1x9a28:6c:07:41:ec:32 5745 -83 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] AirFly_5G5e:ea:1d:8b:2b:58 5745 -86 [WPA2-PSK-CCMP][WPS][ESS] DIRECT-58-HP M130 LaserJetf2:85:c1:92:1e:41 5765 -86 [WPA2-PSK-CCMP][ESS] AIRFLY-921E5228:6c:07:41:ec:31 2417 -85 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] AirFly2a:6c:07:41:ec:31 2417 -86 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] AirFly_Guestdc:fe:18:14:e4:65 5805 -92 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][ESS] 632-5Gf4:28:53:b9:dc:00 5745 -92 [WPA-PSK-CCMP+TKIP][WPA2-PSK-CCMP+TKIP][WPS][ESS] Tony_5G_Oc0:21:0d:45:10:c1 5260 -76 [ESS] X-Link 10C1f4:28:53:a6:ed:f1 5220 -90 [ESS] PIX-LINK_5G2a:6c:07:40:ec:31 2417 -89 [ESS]f4:28:53:a6:ed:f0 2437 -92 [ESS] PIX-LINK_2.4G这⾥也⽀持命令的tab补全功能，现在已经扫描到附近的⼀些wifi热点了，⽐如AirFly,AirFly_5G等是我们办公室的⽆线⽹，由于这个wifi模块不⽀持5G频道，现在只能连接2.4G的，AirFly下⾯我们来添加⼀个刚才扫描的⽹络进来> add_network

0> add_network1 = set network variables (shows list of variables when run without arguments) = set network variables (shows list of variables when run without arguments) = set network variables (shows list of variables when run without arguments)> set_network 1 ssid "AirFly"OK> set_network 1 psk "********"OK现在只是添加了⽹络，还没连接，真正连接命令是enable_network n后⾯的参数n就是刚才设置的那个⽹络 1> enable_network 1OK<3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-SCAN-RESULTS

<3>WPS-AP-AVAILABLE

<3>Trying to associate with 28:6c:07:41:ec:31 (SSID='AirFly' freq=2417 MHz)<3>CTRL-EVENT-STATE-CHANGE id=-1 state=5 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-ASSOC-REJECT status_code=1<3>CTRL-EVENT-STATE-CHANGE id=1 state=0 BSSID=00:00:00:00:00:00 SSID=AirFly<3>CTRL-EVENT-ASSOC-REJECT status_code=1<3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-SCAN-RESULTS

<3>WPS-AP-AVAILABLE

<3>Trying to associate with 28:6c:07:41:ec:31 (SSID='AirFly' freq=2417 MHz)<3>CTRL-EVENT-STATE-CHANGE id=-1 state=5 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-ASSOC-REJECT status_code=1<3>CTRL-EVENT-STATE-CHANGE id=1 state=0 BSSID=00:00:00:00:00:00 SSID=AirFly<3>CTRL-EVENT-ASSOC-REJECT status_code=1<3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-SCAN-RESULTS

<3>WPS-AP-AVAILABLE

<3>Trying to associate with 28:6c:07:41:ec:31 (SSID='AirFly' freq=2417 MHz)<3>CTRL-EVENT-STATE-CHANGE id=-1 state=5 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-STATE-CHANGE id=1 state=6 BSSID=00:00:00:00:00:00 SSID=AirFly<3>Associated with 28:6c:07:41:ec:31<3>CTRL-EVENT-STATE-CHANGE id=1 state=7 BSSID=28:6c:07:41:ec:31 SSID=AirFly<3>CTRL-EVENT-STATE-CHANGE id=1 state=8 BSSID=28:6c:07:41:ec:31 SSID=AirFly<3>WPA: Key negotiation completed with 28:6c:07:41:ec:31 [PTK=CCMP GTK=TKIP]<3>CTRL-EVENT-CONNECTED - Connection to 28:6c:07:41:ec:31 completed (auth) [id=1 id_str=]<3>CTRL-EVENT-STATE-CHANGE id=1 state=9 BSSID=28:6c:07:41:ec:31 SSID=AirFly<3>CTRL-EVENT-DISCONNECTED bssid=28:6c:07:41:ec:31 reason=15<3>CTRL-EVENT-STATE-CHANGE id=1 state=0 BSSID=28:6c:07:41:ec:31 SSID=AirFly<3>CTRL-EVENT-STATE-CHANGE id=-1 state=3 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-SCAN-RESULTS

<3>WPS-AP-AVAILABLE

<3>Trying to associate with 28:6c:07:41:ec:31 (SSID='AirFly' freq=2417 MHz)<3>CTRL-EVENT-STATE-CHANGE id=-1 state=5 BSSID=00:00:00:00:00:00 SSID=<3>CTRL-EVENT-STATE-CHANGE id=1 state=6 BSSID=00:00:00:00:00:00 SSID=AirFly<3>Associated with 28:6c:07:41:ec:31<3>CTRL-EVENT-STATE-CHANGE id=1 state=7 BSSID=28:6c:07:41:ec:31 SSID=AirFly<3>CTRL-EVENT-STATE-CHANGE id=1 state=8 BSSID=28:6c:07:41:ec:31 SSID=AirFly<3>WPA: Key negotiation completed with 28:6c:07:41:ec:31 [PTK=CCMP GTK=TKIP]<3>CTRL-EVENT-CONNECTED - Connection to 28:6c:07:41:ec:31 completed (auth) [id=1 id_str=]<3>CTRL-EVENT-STATE-CHANGE id=1 state=9 BSSID=28:6c:07:41:ec:31 SSID=AirFly这个过程有点长，好⼏秒到最后显⽰CTRL-EVENT-CONNECTED - Connection to 28:6c:07:41:ec:31 completed的时候才是真正连接上了，现在再⽤status看⼀下wifi的状态> status

bssid=28:6c:07:41:ec:31ssid=AirFlyid=1mode=stationpairwise_cipher=CCMPgroup_cipher=TKIPkey_mgmt=WPA2-PSKwpa_state=COMPLETEDp2p_device_address=7c:dd:90:ec:f2:1eaddress=7c:dd:90:ec:f2:1e<3>CTRL-EVENT-STATE-CHANGE id=1 state=9 BSSID=28:6c:07:41:ec:31 SSID=AirFly<3>CTRL-EVENT-CONNECTED - connection to 28:6c:07:41:ec:31 completed (auth) [id=1 id_str=]> quit现在显⽰已经连接上了wifi了，使⽤quit命令可以退出wpa_cli。接下来⽤udhcpc处理ip地址的root@p1:/ # busybox-smp ifconfiglo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:295043 errors:0 dropped:0 overruns:0 frame:0 TX packets:295043 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1

RX bytes:16374716 (15.6 MiB) TX bytes:16374716 (15.6 MiB)wlan0 Link encap:Ethernet HWaddr 7C:DD:90:EC:F2:1E

inet6 addr: fe80::7edd:90ff:feec:f21e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:468 errors:0 dropped:203 overruns:0 frame:0 TX packets:10 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:1000

RX bytes:136293 (133.0 KiB) TX bytes:1248 (1.2 KiB)root@p1:/ # busybox-smp udhcpc -iwlan0udhcpc (v1.20.0) Sending select for 192.168.Lease of 192.168.11.55 obtained, lease time 43200现在获取到⼀个可⽤的ip地址，使⽤ifconfig设置给wlan0root@p1:/ # busybox-smp ifconfig wlan0 192.168.11.55root@p1:/ # busybox-smp ifconfiglo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:326867 errors:0 dropped:0 overruns:0 frame:0 TX packets:326867 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1

RX bytes:18140948 (17.2 MiB) TX bytes:18140948 (17.2 MiB)wlan0 Link encap:Ethernet HWaddr 7C:DD:90:EC:F2:1E

inet addr:192.168.11.55 Bcast:192.168.11.255 Mask:255.255.255.0 inet6 addr: fe80::7edd:90ff:feec:f21e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:765 errors:0 dropped:253 overruns:0 frame:0 TX packets:12 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:1000

RX bytes:225470 (220.1 KiB) TX bytes:1960 (1.9 KiB)⽹络现在算是简单的配好了，可以和电脑端⽤ping命令来看下是否连通在pc上通过cmd窗⼝ping 192.158.11.55C:UsersLXN>ping 192.168.11.55正在 Ping 192.168.11.55 具有 32 字节的数据:来⾃ 192.168.11.55 的回复: 字节=32 时间=23ms TTL=64来⾃ 192.168.11.55 的回复: 字节=32 时间=31ms TTL=64来⾃ 192.168.11.55 的回复: 字节=32 时间=27ms TTL=64来⾃ 192.168.11.55 的回复: 字节=32 时间=18ms TTL=64192.168.11.55 的 Ping 统计信息: 数据包: 已发送 = 4，已接收 = 4，丢失 = 0 (0% 丢失)，往返⾏程的估计时间(以毫秒为单位): 最短 = 18ms，最长 = 31ms，平均 = 24msC:UsersLXN>ping 192.168.11.55正在 Ping 192.168.11.55 具有 32 字节的数据:来⾃ 192.168.11.55 的回复: 字节=32 时间=627ms TTL=64来⾃ 192.168.11.55 的回复: 字节=32 时间=580ms TTL=64来⾃ 192.168.11.55 的回复: 字节=32 时间=275ms TTL=64请求超时。192.168.11.55 的 Ping 统计信息: 数据包: 已发送 = 4，已接收 = 3，丢失 = 1 (25% 丢失)，往返⾏程的估计时间(以毫秒为单位): 最短 = 275ms，最长 = 627ms，平均 = 494ms已经可以ping通，不过貌似不是很稳定，两次ping测试有⼀次丢掉了⼀个包。