2024年5月2日发(作者：u盘xp系统安装教程图解)

Issued 04/14

624

Dulux Trade Ultimate Opaque is a high performance solvent-based exterior coating

which produces a water-repellent satin finish. This product combines a high

performance solid colour with all of the benefits of a premium quality woodstain.

Unique Ultimate wood protection technology from Dulux Trade means exterior joinery

is protected from extreme weather for up to 10 years if used in accordance with

ULTIMATE OPAQUE

instructions, and so looks better for longer.

KEY BENEFITS

• 10 Year Weathershield Protection

• Doors, Windows & Other Joinery

• Solvent-Based

PRODUCT INFORMATION

Typical Use

Suitable for hardwoods and softwoods.

Pack Size

1L, 2.5L and 5L.

Colour Range

See appropriate Dulux Trade colour literature or

visit .

Film Thickness

Film thickness will be dependent upon the

coverage achieved. A nominal figure at 20m

2

per

litre will give a wet film thickness of 50 microns.

Composition (nominal)

Pigment: Organic Pigments, may also contain

titanium dioxide.

Binder: Flexible alkyd resin and a fungicide, for the

purpose of protecting the film.

Solvent: Low Odour Aliphatic Hydrocarbons.

Volume Solids

Opaque colours: 58% (nominal).

SURFACE PREPARATION

To get the best results, ensure surfaces to be

treated are sound, clean and dry. Remove all loose

and defective coatings, if necessary stripping back

to bare wood. Where the surface has been

previously painted, it may be necessary to strip

back to bare wood if the coating is in poor

condition. Special precautions should be taken

during surface preparation of pre-1960s paint

surfaces over wood and metal as they may contain

harmful lead.

Remove and treat any mould, algae, lichen or moss

with Weathershield Multi-Surface Fungicidal

Wash*. Remove defective glazing material, clean

the rebates and any loose or open joints. Replace

any rotten wood and troublesome knots with new

preservative treated timber.

Thoroughly rub down all surfaces in the direction of

the grain to remove any grey, weathered wood and

surface sheen from remaining coatings, and then

dust off (refer to COSHH Assessment).

Prime all bare wood with 2 coats of Aquatech

Preservative Basecoat

+ (BP)

from Dulux Trade

**

including any new or bare replacement beading.

Excess basecoat should be wiped off surrounding

paintwork.

Fill any surface defects, open joints, etc. and

replace any missing glazing material. Do not use

linseed oil putty for glazing (or making good) with

natural wood finishes, use external beads set in an

appropriate non-setting mastic or a special glazing

compound.

New joinery is often factory primed using a stain

basecoat (also called a dual-purpose primer).

These materials quickly erode when left exposed

and may need to be re-primed.

SYSTEMS INFORMATION

STIR THOROUGHLY BEFORE USE. Apply 2 coats

of Aquatech Preservative Basecoat

+ (BP)

from

Dulux Trade

**

to all bare wood. The normal

finishing process is 2 or 3 coats of Dulux Trade

Ultimate Opaque.

When using Dulux Trade Ultimate Opaque, treat

any knots and resinous areas by removing resin

and applying a thin coat of an appropriate knotting

solution in order to help prevent discolouration.

Do not use on resinous wood or woodwork with a

history of blistering. The maximum benefits of this

system will only be realised when used as directed

above on good quality timber that conforms to BS

624

ULTIMATE OPAQUE

EN 942: 2007, in conjunction with good component

design.

Spray Recommendations

This product is not suitable for spray application.

Drying Times

Single coat at standard thickness:

Touch Dry: 4-6 hours.

Recoat: 16 hours.

This system is not suitable for use on exterior

timber where there is severe checking and splitting

of the wood caused by long-term exposure.

For best colour consistency, purchase sufficient

tinted paint for each job including touch-in at one

time from the same source.

APPLICATION METHOD

Brush only. For Health & Safety reasons relating to

all solvent-based paints, spray application is not

recommended.

Cleaning Up

After use, remove as much product as possible

from brushes before cleaning with brush cleaner.

As with all solvent-based paints, this product

should not be applied in temperatures below 5ºC

(as recommended by British Standard BS 6150),

When this paint container is empty please ask your

stockist about recycling. If you have leftover paint,

please dispose of it responsibly and consider

donating it to Community RePaint. Find out more

at /pp.

Practical Coverage

On smooth surfaces of average porosity, a guide to

the practical coverage which can be achieved

under normal conditions is up to 20m² per litre.

Transportation & Storage

Do not use or store in extremes of temperature and

protect from frost. To prevent spillage, please store

and transport upright.

Thinning

This product should not be thinned.

VOC

EU limit value for this product (cat.: A/e): 400g/l

(2010). This product contains max. 299g/l VOC.

VOC content: High (25-50%).

FURTHER SUPPORT

If you need further support, please contact the AkzoNobel Technical Advice Centre on 0333 222 70 70.

*Weathershield Multi-Surface Fungicidal Wash contains: Benzalkonium Chloride.

**Aquatech Preservative Basecoat

+ (BP)

contains Dichlofulanid.

Use biocides safely. Always read the label and product information before use.

Always read full Health, Safety & Environmental Information on can before use.

Safety datasheet (SDS 624) is available free on request by telephoning the AkzoNobel Technical Advice Centre

or by visiting .

AkzoNobel, the AkzoNobel logo, the Flourish logo, Dulux Trade, Weathershield, Aquatech, Community RePaint and the Planet

Possible logo are trademarks of the AkzoNobel group. © AkzoNobel 2014.